XIANYUAlloy · Changzhou
Technical note · 2026-11-10

Why does a Type K thermocouple read low between 250 °C and 550 °C?

The effect is called short-range ordering, or the K-state. It lives in the positive leg, it is reversible, and it is a property of the alloy pair, not a defect in the wire you were sent.

The mechanism: reversible ordering in the positive leg

Between roughly 250 °C and 550 °C the nickel-chromium positive leg of a Type K thermocouple is not stable at the atomic scale. Chromium and nickel atoms in the lattice gradually take up a short-range ordered arrangement. That rearrangement changes the local thermoelectric power, which changes the EMF the wire produces at a given temperature. The wire has not changed its composition; its crystal structure has, and the EMF output shifts with it.

The shift is a few degrees, and the key word is reversible. Hold the wire above roughly 600 °C, or cool it below roughly 250 °C, and the ordering relaxes and the output returns toward the reference curve. Because it reverses, a Type K that sits in the band does not fail; it moves, and it moves differently on a rising cycle than on a falling one. That is why the error shows up as hysteresis rather than as a fixed offset.

How large the effect is

The deviation is commonly one to three degrees Celsius in a Type K element held in the band. Wire that has been cycled through the band many times can show more, with published accounts reaching about five degrees. For a process that sits continuously at 300 °C to 500 °C, that is not a rounding error: it is comparable to the tolerance class the wire was bought to.

Why the same wire reads correctly when cold

Because the effect is reversible, a Type K thermocouple can be perfectly on the curve at room temperature and still be a degree or two off in the middle of its service band. A cold check tells you nothing about the behaviour inside the band. This is the trap that catches a technician who verifies a probe at ambient, installs it, and then finds a persistent low reading at process temperature.

The error also depends on how much of the wire sits in the band. The length of the positive leg that is at 250–550 °C changes the magnitude of the shift, so a probe calibrated at one insertion depth can read differently at another depth even at the same temperature. That is why a calibration done on a bench does not always transfer to the installed configuration.

The check that tells ordering from green rot

The other Type K failure, green rot, is a different animal and it is not reversible. Above roughly 800 °C to 1050 °C in a low-oxygen atmosphere, chromium oxidises out of the positive leg preferentially. The leg becomes depleted of chromium, the EMF falls, the reading drops by tens of degrees, and the wire turns green and brittle. The depletion is permanent.

The two effects do not overlap in mechanism, in temperature range, or in remedy. Green rot is permanent and reads low; the K-state is reversible and can read either direction by a few degrees. A single check separates them: cycle the sensor above 600 °C and re-measure. If the reading recovers, it was ordering. If it stays low, the wire has been permanently altered.

What the reference tables do and do not define

The EMF-to-temperature relationship for the letter-designated thermocouple types is defined by NIST Monograph 175 on the ITS-90, and both ASTM E230 and IEC 60584-1 adopt that reference. The K-state is a deviation of a real wire from that idealised curve, not an error in the curve. This distinction matters when the reading is low: the table is not wrong, the wire is sitting off the table.

What to do about it

  • Budget the one-to-three-degree band as part of the measurement uncertainty where the process dwells in 250–550 °C.
  • Calibrate in the same configuration you will run: same insertion depth, same temperature history, same direction of approach.
  • For a process that must hold tight accuracy across the band and cannot tolerate a few degrees of hysteresis, specify Type N, whose silicon-bearing alloys were designed to suppress short-range ordering.
  • Do not diagnose a low reading as a bad wire on the strength of a cold check alone. Confirm the drift is reversible before replacing the sensor.

When the band matters most

The band covers a large share of real process work. Polymer processing, heat-treat furnaces on the way to temperature, ovens that cycle through the band on every load, and any loop used for control rather than indication all sit in it. For a control loop, a persistent one or two degree low reading is a bias, and it can be larger than the tolerance class the wire was specified to. It is not a safety failure and it is not an open circuit, which is exactly why it goes unnoticed until the product is out of tolerance.

The short version

  • Short-range ordering (K-state) in the nickel-chromium leg shifts a Type K reading by about one to three degrees between 250 °C and 550 °C.
  • The effect is reversible: it relaxes above roughly 600 °C or below roughly 250 °C, so it shows as hysteresis rather than permanent drift.
  • A cold check is not a health check. A wire can be on the curve at ambient and off it inside the band.
  • Green rot is separate: permanent, above roughly 800–1050 °C, low oxygen, and reads low by tens of degrees.
  • Cycle above 600 °C and re-measure to tell ordering from permanent drift.
  • Type N suppresses the ordering by alloy design and is the answer where the band matters.
Questions we get asked
Is the low reading a defect in the wire?
No. It is a reversible change in the atomic structure of the nickel-chromium leg. The composition is unchanged, and the output returns when the wire is cycled out of the band.
How do I confirm short-range ordering rather than green rot?
Cycle the sensor above roughly 600 °C and re-measure at the same temperature. If the reading recovers, it was ordering. If it stays low, the leg has been permanently altered, which points to oxidation or green rot.
Does the tolerance class remove the effect?
No. A tolerance class states how far a new wire may sit from the reference curve. The K-state is a change that happens in service, and it comes on top of the tolerance class.
Citable facts
Sources

Send the specification — diameter, grade, temper, quantity.

We come back with a confirmed lead time and the documentation we can issue for the shipment. 100 g sample at cost; orders from 1 kg.

Request a quotation Order a 100 g sample