XIANYUAlloy · Changzhou
Technical note · 2026-10-26

A 100 A EV charger shunt is manganin, and it is a blade, not a wire

The element is manganin, almost always the CuMn12Ni grade sold as 6J12. It is chosen for two properties: a temperature coefficient near ±10 ppm/K and a thermal EMF against copper of about 1 µV/K, which is roughly forty times lower than constantan's. The part that surprises people is form. At 100 A and 75 mV full scale the element is 0.75 mΩ, and a 1 mm diameter wire of that resistance would be about 1.4 mm long — so commercial shunts are stamped flat blades welded to copper terminals, not wound wire.

The alloy is manganin, and thermal EMF is the reason

Manganin is CuMn12Ni, with a nominal resistivity of 0.43 µΩ·m and a temperature coefficient of resistance of ±10 ppm/K between 20 and 50 °C. Constantan is CuNi45, with a resistivity of about 0.49 µΩ·m and a coefficient of about ±40 ppm/K. On resistivity the two are close. On temperature coefficient manganin is four times tighter. Neither gap is dramatic.

The decisive gap is thermal EMF. Manganin sits at about 1 µV/K against copper; constantan at about 40 µV/K, because constantan is a thermocouple alloy by design and forms the negative leg of Type T and Type J. In a shunt the two ends of the element are bolted to copper busbars that are never quite at the same temperature. That gradient is a thermocouple, and its output adds directly to the millivolt signal the meter is reading. On a 50 mV shunt, a 5 K gradient through a constantan element produces 200 µV of offset, which is 0.4 % of full scale.

For a charger that has to meter energy to a billing class, that offset is the whole error budget. It is also temperature-dependent, so re-calibrating at one temperature does not remove it. Manganin is not a premium choice here; it is the default one.

Why the element is not round wire

Run the geometry. 100 A at 75 mV full scale gives R = 0.075 / 100 = 0.75 mΩ, and at rated current the element dissipates 7.5 W. With manganin's resistivity of 0.43 µΩ·m, a 1 mm diameter wire reaching 0.75 mΩ would need a length of about 1.4 mm. A 1.4 mm wire between two M8 studs cannot be assembled, let alone held to a tolerance.

Real parts solve this by using cross-section instead of length: a short, wide, thin blade of manganin, electron-beam welded or brazed to copper terminal blocks, often with slots laser-cut to trim the value and to cancel inductance. Measured on a catalogue part, a 100 A / 75 mV DC shunt is roughly 100 mm long, 20 mm wide and a couple of millimetres thick over the element. There is no wire in it.

Round wire becomes practical at much lower currents, where the required resistance climbs into the tens of milliohms and the element can be a few centimetres of drawn wire or a multi-strand bundle. That is where a wire mill's product actually belongs: wound shunts, sense resistors and BMS-level current sensing, not 100 A charger blades.

The honest split

If your design is a 100 A charger shunt, you are buying stamped manganin strip and a welding process, not drawn wire. If your design is a wound or low-current shunt, wire is the right form and the alloy grade, the measured temperature coefficient and the certificate are what you should be arguing about with your supplier. A mill that quotes you wire for a 100 A blade is either misunderstanding the drawing or hoping you are.

What to specify, and what actually gets certified

Specify the grade by composition, not by trade name. CuMn12Ni, ±10 ppm/K measured over 20–50 °C, thermal EMF against copper under 2 µV/K, and a resistivity figure quoted with the temperature it applies to. Manganin's resistance peaks in a shallow curve near room temperature, so a resistivity number without a reference temperature is not a specification.

Then separate the two questions that get conflated. The alloy's properties come from the mill and are covered by a material test certificate per batch. The accuracy class of the finished shunt — whether it holds Class 0.5 or 0.2S in a billing meter — comes from the welded assembly, the terminal geometry and the calibration, and cannot be certified by a wire or strip supplier. Buyers who ask a mill for a metering class certificate are asking for something that does not exist at that stage of the chain.

Where this does not apply

Not every 100 A charger shunt is manganin. Low-cost consumer assemblies sometimes use brass or a copper-manganese alloy with a wider temperature coefficient and accept the drift, because there is no billing meter downstream. That is a legitimate engineering choice for a non-metering current limit, and it is wrong the moment the signal feeds a revenue meter.

Nor is 75 mV universal. BMS and embedded sensing often work at 50 mV, which halves the dissipation — 5 W instead of 7.5 W at 100 A — at the cost of a smaller signal to resolve. And whichever output you pick, continuous current should stay near two thirds of the rating; running a 100 A shunt at 100 A continuously asks the element to sit at or above the 80 °C point where manganin begins to drift, with 125 °C the practical ceiling and 140 °C the point of permanent change.

The short version

  • Alloy: manganin, CuMn12Ni (6J12). Constantan is the AC answer, not the DC one.
  • Form: stamped flat blade welded to copper terminals. A 0.75 mΩ wire element would be about 1.4 mm long.
  • Rating: 100 A at 75 mV means 0.75 mΩ and 7.5 W. At 50 mV it means 0.5 mΩ and 5 W.
  • Duty: keep continuous current near two thirds of rating to hold the element under 80 °C.
Questions we get asked
Is a 100 A shunt made of manganin wire?
No. The alloy is manganin, but the element is a flat stamped blade welded to copper terminals. At 100 A and 75 mV the required resistance is 0.75 mΩ, and a 1 mm diameter manganin wire of that value would be roughly 1.4 mm long — too short to assemble between heavy terminals.
Why manganin rather than constantan for an EV charger shunt?
Thermal EMF. Manganin generates about 1 µV/K against copper and constantan about 40 µV/K. In a shunt the terminals sit at slightly different temperatures, so that difference becomes a DC offset in the measured signal. On a 50 mV shunt a 5 K gradient costs 0.4 % of full scale with constantan.
How much power does a 100 A shunt dissipate?
At 75 mV full scale, 75 mV × 100 A = 7.5 W. At the 50 mV output common in BMS work, 5 W. That heat has to leave through the terminals and the surrounding air, which is why high-current shunts are bolted to busbar or cable with real cross-section rather than to a PCB.
Can a wire supplier certify the accuracy class of a shunt?
No. A mill certifies the alloy: composition, resistivity, temperature coefficient, mechanical properties. The accuracy class of a finished shunt depends on the welded assembly, terminal geometry and calibration. Those are the shunt maker's certificates, not the metal supplier's.
Citable facts
Sources

Send the specification — diameter, grade, temper, quantity.

We come back with a confirmed lead time and the documentation we can issue for the shipment. 100 g sample at cost; orders from 1 kg.

Request a quotation Order a 100 g sample